Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Bathroom Remodeling: The Woodland Hills Owner’s Guide
If you own a Mr-Glass bathroom product in Woodland Hills and something has cracked, seized, or stopped sealing, we stock the replacement parts and install them for a typical total of $9,000 to $28,000, depending on what failed and the scope of the surrounding work. Most owners discover the failure the hard way: a shower door that no longer closes square, a glass panel with a hairline crack spreading from a hinge, or a frame that’s pulling loose from the tile. We’re an independent service provider in Woodland Hills, not affiliated with Mr-Glass, which means we can match the right part honestly without pushing one brand over what actually fits your opening.
Before you tear anything apart, read the next two sections. Matching a Mr-Glass part is not as simple as reading a model number off a sticker, and getting it wrong can mean waiting two weeks for a reorder while your bathroom is out of commission.
Which Mr-Glass Models This Applies To
Mr-Glass bathroom products in Woodland Hills fall into two broad generations. The older line, common in homes built through the early 2000s, used 3/8-inch tempered glass with a polished edge and barrel hinges drilled directly into the glass. The newer line moved to 1/2-inch glass with continuous hinge channels and post-mounted hardware. The two are not interchangeable. A 3/8-inch panel will not accept the hinge pins from a 1/2-inch system, and the mounting holes are spaced differently.
The most reliable way to identify what you need is to measure the glass thickness with a caliper, not a tape measure, and to look for a small etched logo or code in one corner of the glass panel, typically on the lower edge near the hinge side. If the etching is gone or too faint, take a photo of the hinge and send it to us. We can usually identify the generation from the hinge geometry alone. For hinges, rollers, and seals, a quality aftermarket equivalent often performs as well as OEM for less money. For the glass itself, we recommend OEM-spec tempered glass. Aftermarket glass that’s cut a sixteenth of an inch off will stress the hinges and crack within a season, and California’s dry heat cycles make that stress worse faster than homeowners expect.
Styles & brands we work with
Signs Your Mr-Glass Bathroom Remodeling Is Failing
- The door drags or catches on the bottom track. This usually means a roller has worn flat or the bottom sweep has hardened. Left alone, it puts lateral load on the hinge screws until they start wallowing out the holes in the tile.
- Water pools at the base of the glass after every shower. The vinyl sweep or the metal threshold channel has failed. In Woodland Hills, the culprit is often the same: hard mineral buildup from our water supply eats the vinyl and corrodes the aluminum channel underneath it.
- A crack runs from a hinge or a notch, not from an impact. That’s tempered glass failing under point load. The hinge was over-torqued at install, or the glass is flexing because the wall is out of plumb. It does not get better on its own, and it does not wait for a convenient time to shatter.
- The handle or knob turns but stops catching. The internal cam or keeper is stripped. This is the single most common Mr-Glass part failure we see in Woodland Hills, and it’s a ten-minute fix when we have the right replacement on the truck.
- Black mold or mildew builds inside the metal channel seams. The gasket has compressed past its useful life. Once water sits in those channels, the metal starts pitting, and the pitting accelerates every additional wet cycle.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Woodland Hills, a Mr-Glass parts replacement typically runs between $9,000 and $28,000 installed. That range reflects how much surrounding work the failure pulls in. Here is the honest breakdown:
- Minor part replacement only (handle, roller, sweep, hinge-set): $300 to $700 per component, which falls inside our smaller-project minimums.
- Single glass panel replacement with OEM-spec tempered glass cut to your opening: $900 to $2,400, including templating, fabrication, and install.
- Full shower door system replacement when the frame, glass, and hardware have all aged out: $4,500 to $12,000, which tracks with our walk-in shower installation range.
- Full bathroom remodel when the failed glass turns into retile, waterproofing, and new fixtures: $9,000 to $28,000, which is the range for a mid-size Woodland Hills bathroom done right.
You get a written price before any work starts. Not an estimate over the phone that grows on the bill. A written price. The finished work carries our 365-Day Done Right Promise: if it is not right within a year of completion, we make it right at no cost to you. That’s 365 days from the completion date, stated plainly.
DIY or Call Us?
Some things on a Mr-Glass shower door are genuinely safe to check yourself. You can inspect the sweep for hardened vinyl, tighten a handle set screw with the correct hex key, and clear mineral buildup from the track. Those are maintenance tasks, not repairs.
What you should not attempt DIY is anything that involves removing or adjusting tempered glass. Tempered glass carries stored tension. Tap the edge wrong and the entire panel detonates into hundreds of small cubes. That is a job for someone who handles it every week, with the right suction cups and a second set of hands. The same goes for any hinge that’s pulling from the wall: the fix usually involves opening the wall to check blocking behind the tile, and that’s a waterproofing decision, not a hardware decision. If you’re not sure which category your problem falls into, call (831) 290-6866 and describe what you’re seeing. We’ll tell you over the phone whether it’s worth a visit, and what the visit will likely cost before we schedule it.
FAQs
The glass itself should last the life of the bathroom. The hardware, seals, and rollers typically last 8 to 12 years in Woodland Hills before mineral buildup and hard-water wear start causing visible problems. Homes with water softeners usually get the longer end of that range. Call (831) 290-6866 if your door is younger than that and already failing, because something was installed wrong, and it’s worth knowing what.
Handles, rollers, and sweeps are replacement-only jobs, and repair is not practical for them. Seals and gaskets can sometimes be re-seated if the channel is clean and un-pitted, but once the metal underneath has corroded, the channel has to go too. We’ll tell you which situation you have when we see it.
A handle or roller replacement takes under an hour. A full glass panel replacement takes three to five business days from templating to install because the tempered glass is cut to order. A full system replacement takes one day on site once the parts are in hand.
We stock the common failure points: standard handles, rollers, sweeps, and hinge sets for both the 3/8-inch and 1/2-inch Mr-Glass lines. Glass panels are ordered per opening because no two openings in Woodland Hills measure exactly alike once the house has settled for a decade or two. We also stock compatible parts for KraftMaid, Cambria, and Silestone products for the surrounding bathroom work.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Woodland Hills, CA at Mason Remodeling Co Woodland Hills, serving Woodland Hills and nearby areas.
