Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Fence Installation: The Woodland Hills Owner’s Guide
ES Windows fence installation in Woodland Hills typically runs $3,500 to $9,000 installed, depending on the style, gate hardware, and whether the fence is tied into an ES Windows screen enclosure or freestanding. We stock common ES Windows-compatible fence sections, post caps, and gate latches, and in most cases we can get your fence ordered, cut, and installed within one to two weeks. Most Woodland Hills homeowners find out a fence section has failed the same way: a hard Santa Ana wind storm pushes a gate past its stop, a post shifts in the dry clay soil, or a powder-coated panel starts showing rust bloom along the bottom rail near sprinkler overspray.
If you’re reading this because a fence section is sagging, a gate won’t latch, or a post is leaning after a wind event, you’re in the right place. Here’s exactly what you need to know about ES Windows fence specs, what fails first, what it costs, and how we handle the repair or replacement in Woodland Hills.
Key Takeaways
- Installed ES Windows fence replacement in Woodland Hills runs $3,500 – $9,000 for a typical residential section or gate rebuild.
- ES Windows fence systems use specific post dimensions and panel spacing; generic big-box fence parts often don’t match without modification.
- Dry, shrinking Woodland Hills clay soil is the number one cause of post lean and gate misalignment we see.
- We’re an independent contractor, not affiliated with ES Windows, and we stock compatible parts for most ES Windows fence lines.
- Call (831) 290-6866 for a free estimate; every quote is written, itemized, and delivered before work starts.
Styles & brands we work with
Which ES Windows Models This Applies To
ES Windows is best known in Southern California for its aluminum window and door lines, but many Woodland Hills homes built from the 1990s through the 2010s included matching ES Windows aluminum fencing around pool enclosures, side yards, and entry courtyards. The fence systems we service fall into two broad families: the ES Windows Series 5800 aluminum fence (2-inch square posts with flat-top panels, usually in bronze or white powder coat) and the Series 7000 estate-style fence (2.5-inch posts with finials and a heavier top rail). The easiest way to identify which one you have is to measure the post: a 2-inch post is Series 5800, a 2.5-inch post is Series 7000. Panels are typically 6 or 8 feet wide, in 48, 54, or 60-inch heights.
The OEM versus aftermarket decision matters here more than with wood or vinyl. ES Windows fence panels use a crimped, riveted rail-to-picket connection rather than welded tabs, and the rail profile is slightly narrower than standard commercial aluminum fence stock. A generic panel from a fence supply yard will often bolt up but leave a visible mismatch at the post face or at the gate reveal. We keep OEM-spec sections and quality aftermarket equivalents from the same extrusion suppliers ES Windows used; we’ll match the picket spacing, rail height, and powder coat color so the repaired section doesn’t read as a patch. Bring us a photo of the fence face and a measurement of the post, and we’ll tell you exactly what you’re working with.
Signs Your ES Windows Fence Installation Is Failing
- Gate drags or won’t latch. The gate post has tilted out of plumb, usually because the concrete footer was poured too shallow for Woodland Hills’ expansive clay. When the soil dries out in summer, it shrinks and the post shifts. A sagging gate is almost never a hinge problem; it’s a post problem.
- Rust bloom at the bottom rail. Sprinkler overspray or pool splash hits the lower rail, the powder coat gets micro-scratched from lawn equipment, and oxidation starts. You’ll see it as bubbling paint or orange pitting first at the rail-to-picket seam.
- Pickles pop out of the rail. The crimped connections loosen over time from repeated wind loading and thermal expansion. One loose picket is cosmetic; four or five means the panel is losing structural integrity.
- Post wobble at the base. Give the post a firm shove. If it moves more than a quarter inch at the concrete line, the footing is failing or the post was never set deep enough. This gets worse every wind season.
- White chalky streaking on panels. Powder coat degradation from UV exposure. It’s cosmetic at first, but once the coating fails, the aluminum underneath starts pitting, and you’re looking at full section replacement rather than touch-up.
Replacement Cost & What’s Included
For a Woodland Hills ES Windows fence section replacement, you’re looking at $3,500 to $9,000 installed for a typical job. A single gate rebuild with a new frame, hardware, and post reset runs $1,200 to $2,800. A full side-yard run of 40 to 60 linear feet with demolition, new posts, panels, and gate replacement falls toward the top of that range. What drives the cost: the Series (7000 estate panels cost more than 5800 stock), powder coat color matching (custom colors add $300 to $600 per job), how many posts need new concrete footings, and whether the fence ties into a stucco wall or an ES Windows screen enclosure that requires custom trim work.
Every quote includes parts, labor, demolition and haul-off of the old section, post setting, hardware, and a written itemized price delivered before we start. No surprise line items, no change orders unless you ask us to add work. Our workmanship on fence installation is covered under our written guarantee for 365 days from completion; if a post shifts or a gate falls out of alignment within that year, we come back and fix it at no charge. That’s the deal, stated plainly.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Aluminum fence work is less dangerous than, say, high-tension garage springs or electric panels, but there are two parts of this job where DIY goes sideways in Woodland Hills. First, post setting: our clay soil expands and contracts seasonally, and a fence post set in a 18-inch hole with a bag of quick-set concrete will lean within two or three years. We dig to a minimum 30-inch depth, use a gravel base for drainage, and set posts in concrete with a slight crown so the base doesn’t hold water. Second, cutting panels: aluminum panel sections are riveted together, and cutting one without the right blade and a jig leaves jagged edges and a bad reveal at the post.
What you can safely do yourself: photograph the label on the back of a panel or the inside of a post cap, measure the post, check your sprinklers for overspray hitting the fence, and note which direction the lean is. That information lets us give you a straight answer over the phone. The actual pulling, cutting, setting, and leveling… that’s what we do. Call (831) 290-6866 and tell us what you’re seeing.
FAQs
An ES Windows aluminum fence in Woodland Hills typically lasts 20 to 30 years with proper post setting and no sprinkler overspray. What shortens that lifespan here isn’t the aluminum; it’s the soil movement against shallow footings and salt or chlorine exposure from pool areas. Fences set on 30-inch footings with drainage routinely outlast fences set at 18 inches by a decade or more.
Call (831) 290-6866 if your fence is showing its age and you want a straight assessment of what’s salvageable.
In many cases, yes, if the rust is caught before the aluminum has pitted past the surface. We sand, prime with an aluminum-specific zinc primer, and powder coat touch-up to match the factory finish. However, if the corrosion has eaten through the rail wall or the picket crimps have failed, patching costs nearly as much as replacement and won’t last. We’ll tell you which one you have.
Call (831) 290-6866 and send us a photo; we’ll tell you which direction to go.
A single gate or a 10 to 20-foot section replacement usually takes one day. A full side-yard run with multiple posts, demolition, and new gate hardware takes two to three days. Concrete cure time adds two to three days before we hang panels on new posts, so expect a total timeline of three to five days for a full rebuild. You’ll get a written schedule in the quote.
Call (831) 290-6866 to get your fence assessed and scheduled for a free written estimate.
We stock common Series 5800 and Series 7000 panel sections, post caps, gate latches, hinges, and the specific riveted picket connectors ES Windows fences use. For less common colors or custom panel heights, we order direct from the same extrusion suppliers; that’s typically a one to two week lead time. We don’t charge you for the part until we’ve confirmed fitment against your existing fence.
Call (831) 290-6866 and tell us your post size and panel height; we’ll check stock while you’re on the phone.
Who You’ll See at the Door
When you call (831) 290-6866, a live person answers; no call trees, no answering service script, no waiting until Monday. Before anyone steps onto your property, we send you the name and photo of the technician who will be there. Every crew member arrives in a clean, marked uniform and shows a photo ID badge at the door before setting foot inside. That’s the Threshold Standard, and it applies on every job, including a fence repair in Woodland Hills. It’s our way of making sure the person you opened the door for is exactly the person you expected.
We’re part of the Threshold Group family, and we’ve been doing this work since 2004. Alongside ES Windows fence systems, we also install and service parts for KraftMaid cabinetry, Cambria surfaces, and Silestone countertops. If you’ve got a mixed project, a fence plus a gate operator, a fence plus a side gate on a bath remodel access path, we’ll coordinate it all on one written quote.
Get the Straight Answer Before You Spend a Dollar
Here’s my approach, and it hasn’t changed since I started working projects around Warner Center and the neighborhoods around it years ago. Tell me what you need done. I’ll tell you what it takes and what it costs. Then we get to work.
Your ES Windows fence isn’t complicated, but it does need to be matched correctly, set deep, and finished so it doesn’t look like a patch job. Send us a photo, let us measure it, and you’ll have a written price in your hand before any work starts. Estimates are free. The price doesn’t change once the work begins unless you add scope. And if it’s not right within 365 days of completion, we come back and make it right at no cost to you.
Call (831) 290-6866 to schedule your free estimate. We serve all of Woodland Hills, including the neighborhoods around Ventura Boulevard, Warner Center, and the hills south of the 101.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Woodland Hills, CA at Mason Remodeling Co Woodland Hills, serving Woodland Hills and nearby areas.
