Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Woodland Hills Owner’s Guide
CGI fence installation in Woodland Hills typically runs $3,500 to $9,000 for a complete panel-and-post system, depending on footage, gate count, and whether we’re cutting into slopes or working around existing hardscape. We stock CGI-compatible fence sections, posts, and gate hardware on the truck, so most swap-outs are done in a single visit. Most Woodland Hills homeowners discover they need this page when a wind event off the Santa Monica Mountains torques a post, or when years of dry-season heat have left a panel rattling loose against its rails.
Which CGI Models This Applies To
CGI’s fence line splits into two families that matter for installation. The original CGI Classic series uses a thinner gauge steel profile, common on homes built from the late 1980s through the mid-2000s. The newer CGI Signature and ProGuard lines run a heavier gauge and use a deeper post channel, which means panels from one line will not seat cleanly in posts from the other. The way to identify yours: look for a small etched code on the inside face of the top rail, usually three letters followed by a four-digit number. No code? Measure the channel width at the post top. Classic channels run 1¾ inches; Signature and ProGuard run 2⅛ inches. That single measurement saves hours of guesswork.
For replacements, we match OEM CGI specs where structural integrity is the concern. For homeowners looking to control cost without losing fit, we can source quality aftermarket equivalents from the same gauge and channel spec. The honest trade-off: aftermarket coatings in Southern California UV conditions tend to show sun fade about two to three years earlier than OEM. Both hold up structurally if installed right. We’ll walk you through the difference before you spend a dime.
One note of transparency: Mason Remodeling Co Woodland Hills is an independent service provider. We are not affiliated with CGI, and we stock compatible parts rather than claiming any factory relationship.
Styles & brands we work with
Signs Your CGI Fence Installation Is Failing
- Posts leaning at the top but solid at the base. The post channel has widened from repeated thermal expansion, and the panel tongue no longer grips. In Woodland Hills, where summer afternoons push fence surfaces past 140°F, this is the most common failure we see.
- Panels rattling in even light wind. The rail-to-post clip has lost tension. It’s a small part, but once one clip goes, neighboring clips carry more load and fail in sequence.
- Visible rust blooming around screw heads or the base of posts. Coastal moisture from the Ventura-side marine layer meets sprinkler overspray, and the zinc coating gives out. The structural post is usually still fine; the fastening points are not.
- Gates that drag along the bottom of the swing arc. The hinge post has shifted inward, usually because the concrete footer was poured shallower than 24 inches. We see this on a lot of tract-home fences in Warner Center neighborhoods.
- Panels that bow outward in the middle. The mid-rail has lost its connection to the vertical stiffener. High wind gusts coming down Topanga Canyon Boulevard flex the panel until the rivet works loose.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full CGI fence installation in Woodland Hills runs $3,500 to $9,000 installed. That range covers panel and post replacement, gate hardware, and post footings where needed. What drives the spread: linear footage is the biggest lever. A 60-foot side yard with one gate sits at the low end; a full backyard perimeter with a double drive gate and slope work hits the high end.
Every quote is written, line by line, before any work starts. You’ll see the material cost, the labor, the post footing spec, and the gate hardware allowance separately. No change orders unless you add scope. Our 365-Day Done Right Promise applies to CGI fence installation the same way it applies to every project we build: if something isn’t right within a year of completion, we return and fix it at no cost to you. Isaac Pruett signs off on every fence job personally before we consider it done.
DIY or Call Us?
For a failing section, there are things you can check safely. Confirm which CGI line you have by measuring the channel width, count the panels showing damage, and note whether posts move when you push the top rail side to side. That’s useful information for any contractor, including us.
What we don’t recommend is pulling posts yourself. CGI posts carry the entire wind load of the panel run, and a post with a compromised bond can release without warning when the retaining screws come out. We’ve also pulled more than one post in this area to find an old gas line closer to the fence line than any marker showed. The risk isn’t worth the saved hour. If you’d rather have this handled correctly the first time, call (831) 290-6866 and we’ll schedule a site look. The estimate is free.
FAQs
Expect 20 to 25 years from an OEM CGI fence that was properly installed, with the caveat that sun-facing side panels in the western San Fernando Valley tend to show cosmetic fade after year 12 while the structure remains sound. Gates and hinge hardware usually need attention around year 10 to 15.
Yes, if the posts are still plumb and the panel metal hasn’t torn at the rail connections. Individual clip replacements, post resetting, and gate hardware swaps are common repairs that cost far less than full replacement. If multiple posts have shifted or the channel is stretched, patching gets expensive enough that new panels make more sense. Call (831) 290-6866 for an exact assessment; we’ll tell you honestly which route is cheaper over the next five years.
A standard panel-and-post replacement on a 60-to-100-foot run usually takes one to two days. New post footings require a day for concrete to cure enough to hang panels, so a full perimeter with several new posts may run to three days. We’ll give you the day count in writing before the job starts.
We keep common CGI-compatible clips, rail connectors, gate hinges, and post caps stocked on our service vehicles in Woodland Hills. Full panels and posts are typically pulled from our yard the same week we scope the job, unless the panel is a discontinued color or profile, in which case sourcing takes a few extra days. We’ll confirm lead time when we hand you the written quote.
Tell me what you need done. I’ll tell you what it takes and what it costs. Then we get to work.
When you’re ready, call (831) 290-6866 for a free estimate on CGI fence installation in Woodland Hills. We’ll send someone who shows up with a name badge, a clean truck, and a written price before a single post hole is dug.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Woodland Hills, CA at Mason Remodeling Co Woodland Hills, serving Woodland Hills and nearby areas.
