Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The Woodland Hills Owner’s Guide
If you’ve got a Barrette roof part that’s failed or failing, we stock Barrette-compatible roofing components and install them throughout Woodland Hills, typically $400 – $1,800 for repairs and $8,000 – $20,000 for full replacements, with most parts matched same-day. Most Woodland Hills homeowners discover the problem the hard way: a water stain on the ceiling after a Santa Ana wind event, granules collecting in the gutter, or a tile cracked clean through from summer heat expansion. The part that actually failed is usually smaller than the damage it caused.
Here’s what you need to know before you spend a dollar: which Barrette parts actually fit your roof, what fails first, what it costs in this market, and whether you should touch it yourself. We’ll cover all of it below.
Key Takeaways:
- Barrette roofing components span concrete tile, clay tile, and stone-coated steel systems, each with different part specs and failure points.
- Most Barrette repairs in Woodland Hills land between $400 and $1,800 installed.
- We’re an independent service provider and we stock Barrette-compatible parts, but we’re not affiliated with Barrette directly.
- If the failure involves structural decking or underlayment, do not walk on it and do not patch it from the inside.
Which Barrette Models This Applies To
Barrette manufactures roofing under several product lines, and the part you need depends on which one sits on your roof. In Woodland Hills, we most commonly see the Barrette concrete tile profiles installed on 1990s-era and newer homes north of Ventura Boulevard, especially in neighborhoods like Walnut Acres and the hills above Valley Circle. The clay tile lines show up on higher-end custom homes around the south side of the 101. Stone-coated steel systems from Barrette are less common here but present on some mid-century remodels.
Here’s the compatibility getcha most homeowners miss: Barrette concrete tiles are not interchangeable across series just because they look similar from the street. The tile profile (barrel, flat, shake-style) determines the head lap, the underlock design, and the fastener pattern. A flat tile from the Barrette 900 series won’t seat correctly on a barrel tile batten system from the 600 series, even if both measure roughly the same length. Before you order anything, check the underside of a loose tile for the series stamp, or measure the exposed width and the side-lock profile. If you send us a photo of the broken tile next to a tape measure, we’ll tell you what series it is, usually within the hour.
On OEM versus aftermarket: Barrette still produces most current tile lines, so OEM-matched replacement tiles are available at most roofing supply houses in the Valley. For discontinued series, quality aftermarket equivalents from U.S. Tile and Boral (now Westlake Royal) often seat correctly if the profile matches. The aftermarket route saves 20 – 40% on materials, but only when you’ve correctly identified the series. We stock common Barrette profiles on our trucks and can order discontinued matches within a few days when a direct swap isn’t available.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Ceiling stains after rain. In Woodland Hills, rain arrives in short, intense bursts, so a small underlayment tear can saturate the decking before you ever see a drip. By the time the ceiling shows a stain, the underlayment under that tile course is usually done.
- Tile granules or clay chips in the gutter. Concrete tiles shed surface aggregate as they age, especially on west-facing slopes that take the afternoon sun. If you’re seeing a steady accumulation, the tile surface is spalling and water absorption is next.
- Cracked or shifted tiles after wind. Santa Ana events regularly exceed 50 mph gusts in the Santa Monica Mountains corridor. A cracked tile at the hip or ridge lets water skip the underlayment entirely and run under the next tile course.
- Broken or rusted flashing at roof intersections. Flashing fails before tiles do, almost always. Around chimneys, skylights, and valley junctures, we see rust-through and lifted edges all over Woodland Hills, often on roofs that are only 15 years old.
- Fastener pop or loose battens. When you hear a tile clack underfoot or see a row that isn’t sitting flush, the batten or the fastener has let go. Walking on it makes it worse. Every step on a loose tile transfers point load to the tile below it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Barrette-compatible roof repair in Woodland Hills runs $400 – $1,800 for a typical job, and full Barrette roof replacement lands between $8,000 and $20,000 depending on square footage, pitch, and access. What moves the number on a repair: how many tiles are broken (most jobs are 3 – 12 tiles), whether the underlayment underneath is compromised, and whether we’re working on a one-story walkable roof or a two-story cut-up with a 6/12 pitch or steeper.
Here’s what you get at each level:
- Minor repair ($400 – $800): Replacement of up to 8 Barrette tiles, re-seating of loose tiles, replacement of 2 – 3 broken fasteners, and a seam check on the surrounding area. Written price before we start.
- Moderate repair ($800 – $1,800): 8 – 25 tiles replaced, flashing repair or replacement at one penetration (vent pipe, skylight edge, or chimney base), and underlayment patching where the deck is dry and intact. Includes a 365-day written guarantee on workmanship.
- Full replacement ($8,000 – $20,000): Complete tear-off of the existing Barrette system, new underlayment throughout, new flashing at all penetrations, and new Barrette-compatible tile or stone-coated steel installed to current code. Permit pulled, inspections passed, written line-item quote before demolition.
Every repair includes a written, line-item price before any work starts, and every job is backed by the 365-Day Done Right Promise. If the repair fails within a year of completion, we come back and make it right at no cost.
DIY or Call Us?
Here’s the honest split. What you can safely do: inspect from the ground with a decent pair of binoculars, clean your gutters, and check the attic after a rain for dark streaks on the underside of the decking. Those are all safe and useful. What you should not do: walk a tile roof unless you know exactly where the battens run, how to distribute your weight, and where the tiles are already compromised. Tile roofs in Woodland Hills fail at the point where someone walked in the wrong spot three years ago, not from age alone. A cracked tile under your heel becomes a broken tile that lets water in during the next rain.
Working on a tile roof also means working at height on a sloped surface, often on the two-story homes common south of the Boulevard. Falls from single-story roofs injure people every year, and a two-story pitch adds real consequence. If the repair involves more than swapping two or three easily reached tiles with a stable ladder setup and proper tie-off, call us at (831) 290-6866. Every one of our roof technicians arrives in a clean marked uniform with a photo ID badge, and you’ll get their name and photo before they ever step on the property. That’s the Threshold Standard, on every job.
FAQs
Barrette concrete tile systems in our climate typically last 40 – 50 years before the underlayment fails, with the tile itself often still viable. The UV exposure and thermal cycling in the Valley is harder on underlayment and flashing than on the tile. Most Woodland Hills homes need new underlayment around year 25 – 30, even if the tile is still sound. Call (831) 290-6866 and we’ll assess what’s actually failing on your roof.
Small edge chips can be sealed, but any crack that runs fully through the tile body needs replacement, not repair. A patched crack reopens with the first heat cycle and lets water behind the tile. Replacement is the only repair that holds. Estimates are free at (831) 290-6866.
Most Barrette tile replacements take two to four hours on site, assuming we have the series match stocked or sourced. Flashing repairs and underlayment patches run longer, sometimes spread across two visits if we need to let a patch cure. We’ll give you a firm timeline with your written quote before we start.
We keep common Barrette concrete tile profiles on our trucks and source matching series from supply houses in the Valley same-day for most calls. For discontinued profiles, we locate aftermarket equivalents or salvage matching tile within a few days. Send us a photo of one of your tiles with a tape measure next to it and we’ll tell you exactly what you’re working with.
No. The written price we give you before the job starts is the price you pay. The only exception is if we open up the roof and find damage that was impossible to see from the surface, and in that situation we stop, show you what we found, and give you a new written price before any additional work proceeds. No surprise invoices.
If your Barrette roof is leaking or you’ve got broken tiles, call us at (831) 290-6866. We’ll tell you what you’re dealing with, what it costs, and who’s coming to your door before we ever set foot on the ladder. Mason Remodeling Co Woodland Hills also carries parts and materials for KraftMaid, Cambria, and Silestone projects, but roofing is what we’re talking about today. Tell me what you need done. I’ll tell you what it takes and what it costs. Then we get to work.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Woodland Hills, CA at Mason Remodeling Co Woodland Hills, serving Woodland Hills and nearby areas.
