Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Woodland Hills Owner’s Guide
Jerith fence installation in Woodland Hills typically costs between $3,500 and $9,000 for a full panel or section replacement, depending on how many linear feet you’re replacing and whether the posts need to be reset. We stock Jerith-compatible aluminum fence panels and hardware on our trucks, and most installations are completed in a single day. Most homeowners discover they need this kind of fence installation after a windstorm snaps a panel loose, a post shifts in the clay-heavy soil, or the gate starts sagging against the latch until it won’t close anymore.
The frustrating reality is that Jerith fencing is built to last decades, but the installation details matter more than the panel itself. What fails first in Woodland Hills is rarely the aluminum. It’s usually the post footing, the gate hinge hardware, or a section that was never properly anchored to begin with. Isaac Pruett has seen every failure pattern this neighborhood can throw at a fence, from roots lifting post footings along Valley Circle to sprinkler rot eating away at wooden fence-to-gate transitions. The fix is straightforward when you know what the original install got wrong, and that’s where a Jerith-specific fence installation service earns its keep.
Which Jerith Models This Applies To
Jerith manufactures aluminum fencing under several residential lines, and compatibility matters more than most homeowners expect. The two series you’re most likely to have in Woodland Hills are the Residential line and the Majesty line. Residential panels use narrower picket spacing and a lighter gauge aluminum, while Majesty panels carry a heavier wall thickness and wider top rail that changes the bracket and post cap fit. If you swap a Residential panel onto Majesty posts, the brackets will not seat correctly, and the panel will rattle in the wind until the screws wallow out the aluminum.
Identifying your panel before you call saves everyone time. Look for a small Jerith label on the inside of the bottom rail or on the post cap underside. If the label is gone, measure the picket spacing from center to center: Residential panels typically run 3-7/8 inches, Majesty panels run closer to 4-1/4 inches. The post size will also tell you what you’re working with: 2-inch square posts versus 2-1/2-inch square posts. For OEM versus aftermarket, we recommend OEM Jerith panels whenever they’re available, because the finish code and baked-on polyester coating are matched exactly. Aftermarket aluminum panels can save you 15-20% upfront, but the finish will weather differently in California sun, and three years later you’ll see the mismatch every time you pull into the driveway.
Styles & brands we work with
Signs Your Jerith Fence Installation Is Failing
- The gate drags or won’t latch. This is almost always a post shifting out of plumb in Woodland Hills’ expansive clay soil, which swells in wet winters and shrinks in summer. The hinge side post moves, the gate drops, and the latch stops lining up with its strike.
- A panel rattles loudly in the wind. The through-brackets that hold the panel to the posts have either loosened or the screw holes have wallowed out from years of minor vibration. Tightening helps temporarily, but a proper fix requires a bracket replacement or a panel re-set.
- White chalky residue on the aluminum. This is oxidation starting where the polyester coating has worn thin, usually at sharp edges or where a sprinkler head has been hitting the same spot for years. Left alone, the aluminum underneath will pit, and the panel loses both looks and strength.
- A post leans visibly, even a few degrees. The concrete footing was either poured too shallow originally, or tree roots have pushed against it. A leaning post eventually torques the panels on either side, and the damage spreads from one section to two to four.
- The fence is solid but the gate section looks… wrong. A previous owner or handyman may have swapped in a non-Jerith gate or modified the hinges. You’ll see extra drilled holes, shims, or hardware that doesn’t match the rest of the fence. This is the most common hidden problem we find on inspection.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Woodland Hills, Jerith fence installation pricing breaks down like this:
- Single panel replacement (6-8 linear feet): $600 – $1,400 installed, including matching panel, brackets, and hardware.
- Gate replacement with new posts: $1,200 – $2,800 depending on gate width and whether a double gate or single gate is involved.
- Partial fence section replacement (30-50 linear feet with new posts set in concrete): $3,500 – $5,500.
- Full perimeter ranch-style install (100+ linear feet): $6,500 – $9,000.
The price spreads come down to three things: how many posts need to be re-set versus reused, soil conditions at the dig (some Woodland Hills yards are pure clay, others hit river rock from the old floodplain), and whether the existing layout is a straight run or has stair-stepping sections that need custom mitered panels. Every quote from Mason Remodeling Co Woodland Hills is a written, fixed price before any work starts. No verbal estimates that grow on the final bill. The work is covered by our 365-Day Done Right Promise, which means if anything isn’t right within a year of completion, we return and make it right at no cost to you.
DIY or Call Us?
Here’s what a homeowner can safely check before calling us: walk the fence line and count how many panels show visible separation at the brackets. Test the gate by lifting up on the latch end, if it moves more than a quarter inch, the hinge post has shifted. Check the post caps and top rails for hairline cracks where sprinklers have been hitting. These are diagnostic steps that help you describe the problem accurately over the phone.
Here’s where DIY goes wrong: resetting a post in Woodland Hills soil properly means digging a footing that goes below the clay’s expansion zone, typically 24 to 30 inches deep and 8 to 10 inches in diameter, then letting the concrete cure before re-hanging panels. If the footing is too shallow, the same failure comes back in one or two seasons. Cutting aluminum panels to fit a custom run without the right blade produces ragged edges that tear hands and snag clothes. And removing an old gate under tension from a warped frame can snap back if the hinges let go at the wrong moment. Aluminum fencing is not high-tension dangerous like a garage door spring, but a falling gate section is heavy enough to break a foot or a finger if it drops while you’re working alone. If any of that gives you pause, that’s the right instinct. Call us at (831) 290-6866 and we’ll take it from there.
FAQs
A properly installed Jerith aluminum fence lasts 20 to 30 years in Woodland Hills, with the baked-on polyester finish holding color for 15 to 20 years before visible fading becomes apparent on sun-exposed sides. The limiting factor here isn’t the aluminum but the post footings, which settle in our clay soil over time and require re-setting much earlier than the panels ever need replacing.
Call (831) 290-6866 if your fence is showing age and you want an honest assessment of repair versus replacement.
A panel with a shallow dent or a single bent picket can often be straightened and re-secured, but a panel that has been hit hard enough to crease the top or bottom rail usually needs replacement. Repairing a creased rail weakens the structural integrity of the panel, and the next wind event will find that weak point. We’ll always price repair and replacement separately so you can make the call with real numbers in front of you. Estimates are free, call (831) 290-6866.
Most single-panel and gate replacements are finished the same day, usually within two to four hours including cleanup. Larger section replacements with new post footings take one to two days depending on how many posts need concrete and cure time before panels go up.
We stock common Jerith-compatible panels, brackets, post caps, and gate hardware on our trucks, so most jobs are completed in one visit. If your specific panel style or color code needs to be special-ordered, we handle the ordering and give you the lead time in writing before any work is scheduled. Alongside Jerith fence hardware, we also stock materials for KraftMaid cabinet touch-ups, and Cambria or Silestone countertop edges if you’re tackling multiple projects. Call (831) 290-6866 and we’ll confirm what we have on hand for your specific fence line.
Mason Remodeling Co Woodland Hills is an independent service provider and is not affiliated with Jerith. We install and repair Jerith fencing based on years of hands-on experience across Woodland Hills, Warner Center, and the surrounding Valley neighborhoods. Tell me what you need done. I’ll tell you what it takes and what it costs. Then we get to work.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Woodland Hills, CA at Mason Remodeling Co Woodland Hills, serving Woodland Hills and nearby areas.
